rattle can paint job tips

Most enamals can be thinned with acetone about 3 to 1 and shot without much expertise. You can also end up with mottling in the paint surface a kind of pebbled texture.

Vwvortex Com Lets See Rattle Can Or Flat Satin Matte Paint Jobs Paint Job Matte Paint Rattle

Harbor Frieght and Home Depot have cheap guns.

. Do the bed first overlap you coats of paint. And something round 4-5 long for radius and barrel channel. Youll be glad you did.

Rattle can paint will NOT hide imperfections. If you prepped your cage the night before there is going to be spider webs and all over it in the morning. Be meticulous in us in your preparation.

The handles that snap on the rattle can helps a bunch. Ill usually start in a certain area like the lower driverside 14 and work my way up and over it gives you good coverage because your not trying to do the whole thing at once which is what leads to what I call Calico paint jobs you usually see. Prime with spraymax 2k primer let dry a coupl days then block with your 150180 grit.

Borrow or rent a small compressor. Dont use rattle cans. I have a total of 60 in that paint job and if I get some rock or tree rash all I need is a 7 can of paint for a touch up.

Wear some kind of mask or respirator or youll be blowing paint out of your nose and lungs for awhile. Use good paint. Start With a Tack Coat.

When you need to mix 2 part stuff you have to find that ratio that works best for you and stay with in that manufacture zone for it to cure right. Paint in a warm clean and dust-free place. This is also a problem in cooler weather.

A can of this rattle paint can cover a wide area so you dont need to worry about it. Use an aerosol clear. Be smooth when you are sanding and dont use too much pressure as you dont want to create any deep scratches.

For a good finish dont worry about wasting paint and make long even overlapping strokes. For best paint job results and to avoid drips and runs move side to side and lay down several thin coats rather than one. Set up a raking shop light and watch for the paint and solvent to level out together and hit the wet look.

Start with 80grit and blocks I use lexan and acrylic sticks. About 1-buck each at Wal-Mart and they last forever. Largest Selection Lowest Prices.

For paint mottling youll need to wet sand by hand or machine - usually a high grit like 2000 3000 or 5000. Get it on a little to thick and it will sag. For best results hold it about 4-6 inches from your surface and spray in short bursts.

If you have a scratch or divot you need to smooth it out before you paint or. Clear the nozzles regularly use even smooth strokes resist the urge to lay it on thick. If you hold your can more than 8-10 inches away you wont achieve the best finish.

Andy The best tip results I get from a rattle-can are to use the spray gun type of handles that attach to the top of the can. Dont fret over mistakes and it is really better to under apply then to over apply. After 80 grit switch to 150-180 grit.

Apr 29 2020. If you find a 73 40 with fuel door upside down bezel and hard-top sporting Rustoleum Sand factory white fiberglass and grey primer for a roof liner that is likely. A rattle can paint jobIts all in how you prep it and spray it.

I dont play with 2 part paints to often and I feel its probably temp sensitive also. Prep your cage well with sand paper scotch brite paint thinner ect. Buy the paint in a quart can and shoot it with a cheap gun.

A uniform coat is more important than an even coat. Rattle can paint likes to run. The texture of the tack coat will help hold the paint in place and reduce runs.

The r-cans need to be warmsame temp as the painting area. And if you look closely it shines just as good as if it were sprayed with a paint gun. Ive seen some pretty nice rattle can paint jobs.

Spray in a parallel line not a curved arc. Get that off now or youll be pissed later. If youre spraying a vertical surface its always smart to apply a tack coat before applying the first full coat.

A tack coat is a light mist that you allow to set for five minutes. Rattle can mistakes often can be dealt with using acetone without damage to real paint. Use a good primer and Ive had good results with clear top coats.

For the overspray or dry spray you can fix by claying or using a clay substitute. Ad Quality Auto Paints 20-70 Off. The entire body frame and hard top are painted with a rattle can.

Wide spray nozzles is the way to go however and. Cover a panel at a time keeping the area wet with paint as you move along. Stock will be pretty straight at this point.

What some of these finishes offer is a much thinner finish vs average rattle can paints. Do the prep right and youll have a nice low buck job thats easy to touch up. Spray Can Tips.

After proper prep work and the proper environment to spray paint the key is uniform paint thickness mills achieved by one person doing the painting knowing basic painting techniques and following the manufacturers directions. To combat this keep the can a good 10-12 inches away form the part and keep the can moving across the part. Rattle up the basecoat paint can ball bearing for at least a minute and then lay it down.

Pin On Car Tips